VITOOS PS1
The VITOOS PS1 is one of its POWER PACK series power supply for effect pedals, with 8 outlets at 9 volts and 2 outlets at 12 volts and 18 volts. If you own some pedals using 18v and you may use them at the same time with your other pedals running at 9v. Some pedals have more dynamics and headroom if you run them at 18v just like Fulltone, Shreadhead and other drive pedals. (Not all pedals can be used with 18v, make sure you read through the manual as any damage will not be covered by warranty) The PS1 will drive ten pedals from the same source. It's more than a power supply, it's a power conditioner which supplies predictable voltage all the time and keeps your pedals in constant performance from one show to another.
Features:
Features:
- Powers eight 9v pedals and two 12v and 18v pedals all at once without losing any signal
- Comes with 10 DC cables to connect your pedals to the PS1.
- Short Circuit Protection
- The LEDs of each 9v OUTLET will light to indicate it is being used
- If the pedal is defective, the PS1 will go in self-protection mode and will auto-restart in about 4 seconds once you unplug the pedal.
- FCLC (Foldback Current Limiting Circuit) provides ultimate protection against power shortages and even at full load, it will stay quiet and cool
- INPUT: AC 100v~240v at 50/60Hz.
- OUTPUT: DC 18v, 1
- POLARITY: Positive Barrel and Negative Center.
- INPUT: DC 18v 1000mA
- OUTPUTS: 9v~100mA (x7), 9v~500mA(x1), 12v~100mA(x1),18v~100mA (x1)
- LEDs: Blue LED for power light
- PS1Power Supply
- AC to DC adaptor
- 10pcs DC cables
- User Manual
CALINE CP-09 TUNER POWER
Features:
Multifunctional, 2-in-1, work as tuner as well as power supply.
Scientific and rigorous tuning program to make tuning more accurate and stable.
With eight isolated outputs, can power eight 9V pedals simultaneously - 6 for 100mA, and 2 for 500mA.
Compact and portable design, easy to carry along.
True bypass design, minimizes tone loss and get more control of your pedal.
Rugged steel casingdurable and sturdy.
Comes with an adapter and 8 connecting cables.
Comes with 4 protective caps to protect petal.
Specifications:
Color: White
Housing: Metal
Adapter input: AC 100-240V 50/60Hz
Adapter output: 18V
Product size: 11.4 * 6.4 * 4.8cm / 4.5 * 2.5 * 1.9in
Product weight: 240g / 8.4oz
Package size: 15.5 * 13 * 8cm / 6.1 * 5.1 * 3.1in
Package weight: 646g / 1.43Lb
Multifunctional, 2-in-1, work as tuner as well as power supply.
Scientific and rigorous tuning program to make tuning more accurate and stable.
With eight isolated outputs, can power eight 9V pedals simultaneously - 6 for 100mA, and 2 for 500mA.
Compact and portable design, easy to carry along.
True bypass design, minimizes tone loss and get more control of your pedal.
Rugged steel casingdurable and sturdy.
Comes with an adapter and 8 connecting cables.
Comes with 4 protective caps to protect petal.
Specifications:
Color: White
Housing: Metal
Adapter input: AC 100-240V 50/60Hz
Adapter output: 18V
Product size: 11.4 * 6.4 * 4.8cm / 4.5 * 2.5 * 1.9in
Product weight: 240g / 8.4oz
Package size: 15.5 * 13 * 8cm / 6.1 * 5.1 * 3.1in
Package weight: 646g / 1.43Lb
CARL MARTIN PRO POWER

Whether you are an international touring musician, or just very particular about the power your pedals are receiving; which by the way you should be, the ‘Carl Martin Pro Power’ power supply was created just for you.
The Pro Power offers a number of features designed with the discerning musician in mind. Start with the switchable (110-230V) AC input, and split that into 8 individual isolated and regulated 9v (150mA) – 12v (110mA) outputs, with extended power at output 7-8 9v (350mA) 12v (220mA), and you have a unique power supply you can use virtually anywhere. There is a simple DIP switch on the back of the ProPower, which allows you to switch the voltage of each output between 9-12v. Housed in our traditional black metal case, the Carl Martin Pro Power is perfect to use on it’s own, or when powering your personal pedal board. The Pro Power also comes with a selection of 9V DC cables for your convenience.
The Pro Power offers a number of features designed with the discerning musician in mind. Start with the switchable (110-230V) AC input, and split that into 8 individual isolated and regulated 9v (150mA) – 12v (110mA) outputs, with extended power at output 7-8 9v (350mA) 12v (220mA), and you have a unique power supply you can use virtually anywhere. There is a simple DIP switch on the back of the ProPower, which allows you to switch the voltage of each output between 9-12v. Housed in our traditional black metal case, the Carl Martin Pro Power is perfect to use on it’s own, or when powering your personal pedal board. The Pro Power also comes with a selection of 9V DC cables for your convenience.
DUNLOP DC BRICK

MXR M237 DC Brick Power Supply
Put an MXR M237 DC Brick on your pedalboard and you’ll never have to change batteries again. The compact DC Brick can run 10 of your favorite pedals with 8 9-volt outputs that combine to deliver up to 1,200 milliamps of clean steady power, and 2 18-volt outputs that can power a total of 800 milliamps for maximum efficiency from each pedal on your board. The new DC Brick has all of the short circuit and overload protection of the original DCB10 with twice the power. Each 9v output has its own red LED that lights up to indicate a short, so any power problems on stage or in the studio can be immediately identified and fixed. The MXR M237 DC comes with its own 18v AC adaptor and 10 connector cables.
MXR M237 DC Brick features:
Put an MXR M237 DC Brick on your pedalboard and you’ll never have to change batteries again. The compact DC Brick can run 10 of your favorite pedals with 8 9-volt outputs that combine to deliver up to 1,200 milliamps of clean steady power, and 2 18-volt outputs that can power a total of 800 milliamps for maximum efficiency from each pedal on your board. The new DC Brick has all of the short circuit and overload protection of the original DCB10 with twice the power. Each 9v output has its own red LED that lights up to indicate a short, so any power problems on stage or in the studio can be immediately identified and fixed. The MXR M237 DC comes with its own 18v AC adaptor and 10 connector cables.
MXR M237 DC Brick features:
- 8 - 9v Outputs, 1,200 mA Combined
- 8 - LED Short Circuit Indicators
- 2 - 18v Outputs, 800 mA Combined
- Overload Protection
- 10 Connector Cables
- 18v Adaptor Included
- 4.25” (10.79 cm) x 2.312” ( 5.87 cm) x 1” (2.54 cm)
JOYO JP-02

JOYO JP-02 Power Supply - 10 filtered outputs each with an isolated short circuit & over current protection. Version 3. 00 JP-O2 filtered 10 x power supply 2 from JOYO technologies. A power supply which now adds more power outputs with extended power output ratings. Built in a rugged steel casing and now featuring a new slim design to fit almost any existing pedalboard configuration and all necessary power link cables included.
The new JP-02 feature the following power options, all isolated short circuit & over current protection of a DC 9 volt power output with EACH output of 100mA.
Suitable for most analogue 9 volt effects with centre negative polarity. (Check the back of your pedal if you are not sure!). Also DC 9 volt power output but with maximum output of 500mA, which is suitable for many digital effects as well when more power is required for other units on the board.
Output 9 gives a DC12 output, the maximum output current is 100mA and is used for effects requiring 12 volt of power.
Output 10 gives a DC18 output, the maximum output current is 100mA for effects or other things that carry this rating. All outputs are fully regulated and offer Isolated short circuit protection, meaning if one output is overpowered beyond the power rating for any reason, all other outputs will not be affected.
Also featuring Blue LED's at every output. Great for dark stages and gives your board a nice blue glow.
SPECIFICATION
• Ten Isolated Output 10
• Isolated Short Cricuit/Overcurrent Protected
• Powers For 9V、12V or 18V PEDAL
• Bright Blue LED For Pedal Board Lighting & Short Circuit Indicate
• Includes Cable
The new JP-02 feature the following power options, all isolated short circuit & over current protection of a DC 9 volt power output with EACH output of 100mA.
Suitable for most analogue 9 volt effects with centre negative polarity. (Check the back of your pedal if you are not sure!). Also DC 9 volt power output but with maximum output of 500mA, which is suitable for many digital effects as well when more power is required for other units on the board.
Output 9 gives a DC12 output, the maximum output current is 100mA and is used for effects requiring 12 volt of power.
Output 10 gives a DC18 output, the maximum output current is 100mA for effects or other things that carry this rating. All outputs are fully regulated and offer Isolated short circuit protection, meaning if one output is overpowered beyond the power rating for any reason, all other outputs will not be affected.
Also featuring Blue LED's at every output. Great for dark stages and gives your board a nice blue glow.
SPECIFICATION
• Ten Isolated Output 10
• Isolated Short Cricuit/Overcurrent Protected
• Powers For 9V、12V or 18V PEDAL
• Bright Blue LED For Pedal Board Lighting & Short Circuit Indicate
• Includes Cable